DJI Phantom 3 Firmware

Discussion in 'DJI Phantom 3 Downloads' started by gustofusion, Feb 7, 2016.

  1. gustofusion

    gustofusion Key Holder
    Staff Member Registered User

    Joined:
    Feb 6, 2016
    Messages:
    126
    Media:
    26
    Albums:
    2
    Likes Received:
    32
    Wanted to provide a dedicated location for various DJI firmware. Read and pay attention below for the firmware you may need that is no longer available from DJI.

    Transmitter
    C1_FW_V01.03.0020

    C1_FW_V01.04.0003

    C1_FW_V01.04.0030


    Aircraft
    Phantom_3_Professional_Firmware_v1.1.8_en

    Phantom_3_Professional_Firmware_v1.1.9_en

    Phantom_3_Professional_Firmware_v1.2.6_en

    Phantom_3_Professional_Firmware_v1.3.20_en

    Phantom_3_Professional_Firmware_v1.4.0010_en

    P3X_FW_V01.05.0030

    P3X_FW_V01.06.0040


    DJI PC Flight Simulator
    DJI_PC_Simulator_Installer_And_User_Manual_V1.0_en


    DJI Go App (IOS)
    DJI_Pilot_1.1.2
    DJI_GO_2.6.0


    DJI Go App (Android)

    DJI-Pilot-1.0.7_android
    DJI_Pilot_1.1.2_android

    DJI Factory Service .bin
    This file will allow you to remove any firmware you have on your Phantom 3 and replace it with any version you like.

    Format your sd card from your computer, not the pilot app.
    Place the .bin file from inside the MVOM0F.zip file on the card in your Phantom 3 and power it up.
    You will hear 4 beeps in a row, this will go on for several minutes.

    When you hear 1 long beep followed by 2 short beeps it's now safe to turn off the Phantom.

    Format the sd card again then place the firmware of your choice on the sd card and place it in your Phantom then power on the Phantom. Listen for the same series of beeps as outlined above.

    Once you have finished you can check the version of firmware from within the Pilot app. Remember to conduct an IMU calibration as well as a compass calibration before flying your Phantom after the firmware installation.



    Log into download the MVOM0F.zip file
     

    Attached Files:

    #1
    Last edited: May 11, 2016
  2. Albertus de Wet

    Registered User

    Joined:
    Apr 27, 2016
    Messages:
    1
    Likes Received:
    1
    Gustofusion
    I had the same problem as many others on the Forums reported after upgrading to the lastest firmware 1.08.0080.
    I have upgraded up to 1.06.xx without any problem and I skipped 1.7.xx.
    I got a 'No signal' error on the app (android) and tried to backout the 1.8 firmware - no luck.

    I downloaded this MVOM0F file and put the .BIN file (as the only file) in the root of the newly formatted 32GB SD card (formatted on my laptop).

    Well, I put it in the camera and turn on the P3P - no luck - light just stays on green.
    I turned it off, removed the SD and retried - same thing - no wiping or any sounds as you describe.

    I tried another SD card - same thing.

    What is going on?Any ideas?

    UPDATE:
    I played with different cards and tried it numerous times....I could NOT hear the sounds you described....HOWEVER...I reformatted one card again, put the latest firmware 1.8.0080 on it and NOW it's updating.
    Instead of just a constant red led and a long D----- sound , I am getting the red/green LED's and the update seems to be taking.

    SO: your fix did seem to work - but I did not get the sounds effect :)

    Thanks a million - now just hope that I get the connection established after the update is complete.

    This program is a winner!

    Take care
     
    #2
    Last edited: Apr 27, 2016
    gustofusion likes this.
  3. FDNYFISH

    FDNYFISH New Member
    Registered User

    Joined:
    May 18, 2016
    Messages:
    1
    Likes Received:
    0
    does this MVOM0F file work with a Inspire 1?
     
    #3
  4. gustofusion

    gustofusion Key Holder
    Staff Member Registered User

    Joined:
    Feb 6, 2016
    Messages:
    126
    Media:
    26
    Albums:
    2
    Likes Received:
    32
    What it will do is remove the current firmware so you can then install whatever version you would like to install. Keep in mind you can only install A variety of firmware for the inspire.
     
    #4
  5. droned

    droned Member
    Registered User

    Joined:
    May 24, 2016
    Messages:
    3
    Likes Received:
    1
    does it work with phantom 3 advanced ?
     
    #5
  6. droned

    droned Member
    Registered User

    Joined:
    May 24, 2016
    Messages:
    3
    Likes Received:
    1
    i tried and had no effect on my p3 advanced ruling 1.8fw. do you have any other magic wipe file ?
     
    #6
  7. selim

    selim New Member
    Registered User

    Joined:
    May 24, 2016
    Messages:
    1
    Likes Received:
    0
    hi there is no file?!
     
    #7
  8. Donnie

    Donnie New Member
    Registered User

    Joined:
    Apr 22, 2016
    Messages:
    1
    Likes Received:
    0
    Did you have any luck ? Did you extract the BIN file and load it to the aircraft ?
     
    #8
  9. gustofusion

    gustofusion Key Holder
    Staff Member Registered User

    Joined:
    Feb 6, 2016
    Messages:
    126
    Media:
    26
    Albums:
    2
    Likes Received:
    32
    Try the DJI site for any other versions you may need, you can at least remove a version you do not like or want on your equipment.
     
    #9
  10. Aaron Hurd

    Aaron Hurd New Member
    Registered User

    Joined:
    Sep 6, 2016
    Messages:
    1
    Likes Received:
    0
    Morning Gustofusion,
    I've been running the 01.06.0040.bin for a while and just this last weekend I get the dreaded need to update to the latest firmware. So it looks like I'm only a few behind but I don't want to go thru the long process of updating each firmware. I tried to use the MVOMoF.bin file with no luck. I've tried several time with a few different MicroSD cards. I also tried to just go thru and update the very next .bin file with no luck.... it sounds like the P3P is starting to update then I get a very long beep.....that dosen't stop. I have to turn off the drone as it dosen't sound like the update is going as it should.........any ideas what might be going on.
     
    #10
  11. Steve Thuemmel

    Steve Thuemmel New Member
    Registered User

    Joined:
    May 19, 2016
    Messages:
    1
    Likes Received:
    0
    I am trying to download DJI Pilot 1.1.2, but it is not working. It takes me to the video page. http://hypedphoto.com/dronevideos/wp-content/uploads/2016/01/DJI_Pilot_1.1.2.zip and it says file not found
    What am I doing wrong?
    thanks
     
    #11
Loading...

Share This Page